|
700/900 Series General Forum for the Volvo 740, 760, 780, 940, 960 & S/V90 cars |
Information |
|
740 Axle Torque Rod BushesViews : 534 Replies : 8Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Jun 12th, 2021, 14:19 | #1 |
Member
|
740 Axle Torque Rod Bushes
Hi
I've just replaced the torque rod bushes, on both rods top and bottom. I've used polybushes, I'm wondering if this was a mistake. When driving now under acceleration or deceleration, they is vibration from the back, has anyone any thoughts on this?. The poly bushes are round whereas the original was convex. Many thanks Andrew |
Jun 12th, 2021, 16:32 | #2 |
🤍💙💗
Last Online: Today 03:08
Join Date: Mar 2006
Location: Lichfield
|
Yep, had vibration after fitting them at full load around 2000-2500 rpm and decelerating through that rpm too. IIRC it did eventually get a bit better after a while, but still there. Presumably when they softened up slightly.
Had even more vibration when fitted the TTV flywheel between 1000-3000 rpm, to the point where it was undriveable. Replaced the gearbox mount, donut, centre bearing and carrier, no dice. Replaced the big bushes with standard rubber and now its back to the vibration at full boost around 2300 rpm. The small bushes should be fine to replace with poly, but the big ones are designed like an hourglass for a reason.
__________________
MY97 940 CD LPT Super Sports Edition 2 Turbo, Midnight Purple, 175,000 miles. |
The Following User Says Thank You to baggy798 For This Useful Post: |
Jun 12th, 2021, 19:32 | #3 |
Ye olde Volvii galore!
Last Online: Dec 18th, 2023 11:23
Join Date: Oct 2017
Location: Sherborne
|
As a slight deviation (apologies for threadjacking!), I need to change the torque rod bushes on my 940 diesel estate...is it a job that requires any specialist kit or is it a viable driveway job?
__________________
Barges of Distinction: '96 945 SE LPT M90 '95 945 GLE D24TIC M90 ‘88 745 GL B200E M47 |
Jun 12th, 2021, 19:36 | #4 |
Member
|
740 Axle Torque Rod Bushes
Thanks, I will get them replaced with the proper ones, at least their all cleaned up ready this time to just put the new ones in.
|
Jun 12th, 2021, 20:37 | #5 | |
Member
|
740 Axle Torque Rod Bushes
Quote:
I used an hydraulic press to get the old ones out and that combined with a vice for re-fitting the bushes. I was able to replace a small section of fuel pipe that started leaking with me messing about, so glad that showed up when it did. Round 2 when the rubber ones arrive. Andrew |
|
Jun 13th, 2021, 10:33 | #6 |
Trader Volvo in my veins
Last Online: Today 20:52
Join Date: Dec 2004
Location: Anglesey
|
Did you do the axle clamp bushes and the front of the lower arm.
Adding poly bushes in one location will show up wear in other parts and make it feel worse than when it was all sloppy |
Jun 13th, 2021, 13:41 | #7 | |
Member
|
740 Axle Torque Rod Bushes
Quote:
Possibly best I do the rest first and then see, rather than just part of it. Many Thanks |
|
Jun 13th, 2021, 17:49 | #8 | |
Premier Member
Last Online: Today 19:03
Join Date: May 2012
Location: Lakenheath
|
Quote:
While you're under there, i suggest you drop the tank out and renew the rubber fuel hoses all in one go. Mine had a mixture of 12mm and 8mm bore hoses, i suspect yours will be the same. Fit new fuel hose clips as well.
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ |
|
The Following User Says Thank You to Laird Scooby For This Useful Post: |
Jun 13th, 2021, 19:27 | #9 |
Member
|
It was a metal section that was leaking, I have about 8 months ago removed the tank and replaced the hoses, the leak was about 2 inches away from the smaller hose connection, so I cut the metal leaking bit out and fitted a new hose again but longer, I was able to replace a plastic fuel pipe clip at the same time which was good.
This is the second leak from a metal section of fuel pipe, they were both on a bend. After this im changing the fuel filter and was going to clean the remaining fuel pipe, so may find another leak possibly. Andrew |
The Following User Says Thank You to panda529e699 For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|