|
200 Series Articles How to's and Guides for the 200 series. |
Information |
|
Guide to rustproofingViews : 10839 Replies : 4Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Jan 29th, 2011, 22:34 | #1 |
Former contributor
Last Online: May 15th, 2024 09:52
Join Date: Dec 2004
Location: Rhosgoch, Anglesey
|
Guide to rustproofing
There has been a lot of discussion about rustproofing 240s. Have just stripped a 240 estate to bare shell I thought I would post some pictures to show the areas that will benefit from waxoyling. I would appreciate any comments and suggestions so we can build up a good guide.
I'll start from the back. One of the very common problem areas on both saloons and estates is where the floorpan meets the rear panel. You can see how they both curve in and are then spot welded together. This makes a good rust trap. This estate is good which is unusual. A good application of waxoyl to the inside of the join is a good idea: Moving forward another area with a spot welded lip is the wheel arches. From inside a good amount of waxoyl can be applied between the wing and inner arch. Moving forward to the sills there are access points along the length covered with a plastic plug. This one has less available being a later model so rerar half would be accessed through the seat belt mounting. Also the B pillar can be treated paying special attention to where the hinges are mounted. Also be careful not to block the drain holes in the sills as these drain the water from the air intakes. This one shows the front part of the sill and the other cpommon rot point which is the A pillar as can be seen here is already rusting: This one shows the problem with the A pillar better. In front of the A pillar early cars have a vent which provides access to the void that takes the water down from the air intake - another place to waxoyl. The other obvious areas are the bottoms of the doors (keep drainage holes clear). It is worth ensuring the plastic in the door is intact as this keeps water from damaging the door cards. Also bottom of the tailgate or boot and the leading edge of the bonnet. Mike
__________________
A Volvo is for life not just for Christmas! |
The Following 2 Users Say Thank You to Mike_Brace For This Useful Post: |
Jan 30th, 2011, 09:08 | #2 |
Ovlovnut
|
Another common point is around the rear shock mount area. You may recall my finding these holes in 'Tank' a while back.
If you can get to these early enough (like I did by chance) it will not be too bad. A mechanic inspected mine & found it only to be the inner floorpan. Under the car was solid & is now waxoyled. As Mike pointed out, that lip at the rear. Mine was apparently quite good! Repairs, well mine ended up like this, a small plate was spot welded over the biggest hole inside the car. I then sprayed waxoyl down into the cavities. Filled the holes with instant metal & slapped 2 coats of Hammerite on. Under the bumper, I Kurusted, filled with fibre resin, then put 2 coats of Hammerite on. The area cannot be seen once the bumper is back It only takes a few minutes to check these points, & those Mike points out. It will be a few minutes very well spent
__________________
2004 V70 2.4SE Auto 'The Welshmobile’ 2002 Laika Ecovip 400i ( Motorhome on an Iveco 2.8TD) http://www.gitessouthbrittany.com/ http://moncopainmonchien.jimdo.com/ |
The Following User Says Thank You to Paul240480 For This Useful Post: |
Jan 30th, 2011, 12:08 | #3 |
240SE
Last Online: Mar 4th, 2019 20:44
Join Date: May 2007
Location: Strath Brora
|
Great Mike, the start of another excellent 'How to'.
The mechanic I use gave me some 'Add-It Clear Grease' spray which he uses on exposed surface rust. Areas like trailing arms or suspension members that are meaty bits of metal that just have a corroded surface. It sprays realy thin and then starts to creep and get more viscous, but never fully dries. It has big temperature tollerences and seems to resist being worn off by water etc when driving.
__________________
240 SE Auto 1991 |
Jan 31st, 2011, 20:56 | #4 |
Master Member
|
Damn you more work for the summer ,pointless trying this time of the year the water you dunk the waxoyl can in to get it fluid goes cold to easily.
found a brand new tin at a bootfair yesterday for £2 so i have no excuses to not to |
May 31st, 2011, 20:02 | #5 |
Ovlovnut
|
Reading this thread: http://www.volvoforums.org.uk/showthread.php?t=125920 prompted me to search for this one that Mike started. It was intended to become a guide with folks adding there findings as and when to provide a mass of information about the dreaded 'tin worm'. One from which we can all benefit.
So here it is 'bumped'. PLEASE do add to it. I'll give it a couple of days and then will ask for it to be added to 'articles' with a link back to this 'original thread' like the others . Thanks for reading Link to original thread.
__________________
2004 V70 2.4SE Auto 'The Welshmobile’ 2002 Laika Ecovip 400i ( Motorhome on an Iveco 2.8TD) http://www.gitessouthbrittany.com/ http://moncopainmonchien.jimdo.com/ Last edited by cumbrianmale; Jun 6th, 2011 at 18:24. |
The Following 3 Users Say Thank You to Paul240480 For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|