Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > PV, 120 (Amazon), 1800 General > PV, 120, 1800 Articles

Notices

PV, 120, 1800 Articles How to's and Guides for the PV, 120, 1800 series.

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

Screen removal / re-fitting

Views : 11710

Replies : 0

Users Viewing This Thread :  

Reply
 
Thread Tools Display Modes
Old Jan 3rd, 2009, 11:07   #1
Gordon Hunter
Ex 1800 Register Keeper
 
Gordon Hunter's Avatar
 

Last Online: Apr 29th, 2022 18:04
Join Date: Dec 2001
Location: Central Scotland
Default Screen removal / re-fitting

A 40 year old car windscreen can take a fair battering over the years. While a level of stone chipping can be acceptable even to the MOT man, there will come a point when the screen really needs replacing. Even small chips can suddenly develop into an MOT failure and I have seen cars where carelessly fitted or badly worn wipers have left nasty scratches on the screen that cannot be polished out.

In the workshop I have been converting a left hand drive 1966 P1800S Californian import over to right hand drive. As the screen needed to come out anyway, this project will make a good visual aid to illustrate the procedure. The same principles will be applicable to the Amazons although you will have to remove the interior trim too.

How you remove the screen and trim will depend on which parts if any that you are re-cycling. If the screen rubber is in good condition then it is well worth re-using as this will save money and be a lot easier to fit than a new seal.
If the trim is good but the rubber is shot, then it is far easier just to cut the trim out of the rubber with a Stanley knife than risk warping it. Don't worry if you do bend the trim slightly, as it is made from aluminium (excepting the earlier P1800's which are made from chromed brass) and can be re-shaped to a degree with the edge of a scraper.
Removing the old screen can be done after the trim is out. I use three or four large paint scrapers to prise back the rubber from the inside of the car and lock it facing backwards to its normal position in the aperture. The screen can then usually be pushed out with even pressure from the inside of the car enough for an assistant on the outside to pull the rubber outwards over the aperture at one of the corners. Once this first part of the screen rubber is out, it is relatively straight forward to work your way round the rest of the screen with the assistant and remove enough of the rubber to pull the screen out.
Now is the time to remove any remains of the old sealer and make sure that any rot in your screen aperture is repaired so that a smooth and even surface is left to fit the new screen to.
The original screen sealer that Volvo used dries rock hard and you will have to chip this off with a scraper! If you are very careful, it is possible to avoid chipping the paint around the screen and having to re-finish this.
Please ensure that you wear proper eye protection when carrying out this part of the preparation...


1.) To refit, first fit the rubber to the new screen while it is off the car.
Before offering it up to the aperture, I fit a length of ordinary household speaker cable loaded into the inside facing groove in the rubber. This wire will give us the necessary leverage to pull the screen rubber over the aperture lip when it is fitted in place...


2.) Once you are sure that the screen is lined up well in the aperture, get an assistant to push down on the front of the screen with even pressure. you can now pull the wire out, forcing the rubber over the inside of the aperture...


3.) Now its time to prime underneath the rubber seal with a flexible sealant of the kind that never fully dries. I always err on the generous side with the sealant. Fitting the trim will force the sealant into any gaps in the aperture. This will make quite a mess but any excess can be cleaned off later with a rag and some white spirit. Although the sealant is the non-setting variety, don't leave the next stages and cleaning up for too long as the sealant becomes less malleable after a few hours...


4.) Next the speaker wire is forced into the trim groove in the rubber. This enables the rubber lip to be lifted up high enough to accept the trim...


5.) Proceeding one side at a time, fit the trim into the grove in the screen rubber and use a trim tool such as the one in the photo to ensure that the rubber lip seats over the top lip of the trim. There is quite a knack to this, but with a bit of patience you'll get it in...




6.)Fit the remaining trim section, remembering to fit the two joining sections in place. You can use the scrapers to further manipulate the trim into the rubber. Slide the joining strips along and stand back and admire your hard work!..



Gordon Hunter
1800 Register Keeper
Attached Images
File Type: jpg Preparation.jpg (52.7 KB, 62 views)
File Type: jpg Screen & trim fitting 1.jpg (39.2 KB, 60 views)
File Type: jpg Screen & trim fitting 2.jpg (38.3 KB, 65 views)
File Type: jpg Screen & trim fitting 3.jpg (41.9 KB, 63 views)
File Type: jpg Screen & trim fitting 4.jpg (51.1 KB, 63 views)
File Type: jpg Screen & trim fitting 5.jpg (41.0 KB, 71 views)
File Type: jpg Screen & trim fitting 6.jpg (44.2 KB, 72 views)
File Type: jpg Screen & trim fitting 7.jpg (53.5 KB, 64 views)

Last edited by 222s; Nov 21st, 2013 at 20:47. Reason: reattaching photos
Gordon Hunter is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 12:35.


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.