Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > 700/900 Series General > 700/900 Series Articles

Notices

700/900 Series Articles How to's and Guides for the P700/900 series.

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

'How To' Guide: B230FK Crank Position Sensor Replacement

Views : 9224

Replies : 0

Users Viewing This Thread :  

Reply
 
Thread Tools Display Modes
Old Aug 9th, 2018, 09:50   #1
LPTJoe
Senior Member
 

Last Online: Mar 25th, 2022 06:54
Join Date: May 2018
Location: Southampton
Default 'How To' Guide: B230FK Crank Position Sensor Replacement

As per the title, I tackled this job this morning so thought why not take some pictures and create a DIY guide as it seems a common issue.

N.B: I tried posting this in the '700/900 articles' section but unfortunately was met with a message stating that I don't have permission? If a mod could possibly move this there if possible that would be great....

Step 1.

Decide you'd like to replace your crankshaft (Pulse) sensor. This could be for simple preventative maintenance, because of a no start condition or because you've found the wiring to be damaged like mine...



Step 2

Gather the bits you need...

1. New sensor (Mine was just under £40 trade price from Volvo)
2. 10mm ratchet spanner
3. Assortment of ratchet/10mm socket/extensions/uj's
4. Copper grease
5. Electric contact cleaner spray
6. Snips
7. Cable ties.
8. Torch





Step 3

Disconnect the cable tie harness fitting from the firewall by simply lifting it free of the tab it sits on at the back and then look at it, there's a little lever that when pushed allows you to open the cable tie section to make it loose and withdraw the wiring/loom. This allowed me so remove the old CPS without destroying it's wiring completely so as I can keep it as a spare just in case.

Once you've done this you simply need to follow the wire from the plug down to the bellhousing, there you will find the sensor (Arrowed in green) It's a bit fiddly but is only held on by one 10mm bolt.



Step 4

Undo the 10mm bolt, remove the clips holding the wiring to other stuff along it's course and unclip and remove the plug. Remove the sensor and wiring from the car and compare it with your new part to ensure they match...



Step 5

Spray inside the plug fitting from the loom with contact cleaner to ensure a good connection, lightly cover the end of the bolt with copper grease and re install everything in the reverse order of removal. The bolt does not need to be too tight, DON'T STRIP IT!!!! Re-seat the loom support/cable tie to the firewall with loom in place and perhaps tidy up the extra wiring from the newly installed sensor with a couple of extra cable ties.



Step 6

Stand back and feel satisfied that the job is complete. it took me 20mins at a very relaxed pace and that included time to take pictures. In the end I didn't use the socket set and TBH could have done without lots of the gear pictured. At a push all that's needed is some snips and a 10mm spanner.

HTH.

Original Topic for discussion: Here

Last edited by CTCNetwork; Sep 4th, 2018 at 09:11. Reason: Added topic link
LPTJoe is offline   Reply With Quote
The Following 4 Users Say Thank You to LPTJoe For This Useful Post:
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 01:41.


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.