Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > 200 Series General > 200 Series Articles

Notices

200 Series Articles How to's and Guides for the 200 series.

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

Simple rear trailing arm bush tool

Views : 9980

Replies : 0

Users Viewing This Thread :  

 
 
Thread Tools Display Modes
Old May 28th, 2011, 11:47   #1
DW42
Senior Member
 

Last Online: Oct 9th, 2022 04:41
Join Date: Feb 2011
Location: Currumbin, Queensland
Default Simple rear trailing arm bush tool

I have just done the dreaded rear TAB replacment on my 240. I was hoping to use the original shell with poly bushes, as detailed by Mike Brace on this forum. But the shell on one side of my 240 had a rust hole in it, so I couldn't do this easy option, and had to install Volvo rubber bushes.

Having looked at how to make a homebrew rear TAB tool at:
www-ese.fnal.gov/.../volvo_trailing_arm_bushing_tool.htm
I found it quite difficult to source a pipe coupling in the UK like the one required to make the tool. I also didn't think I could drill through it accurately first go. So I made a similar tool out of washers, a hole saw, and a nut and bolt. This is what I used (washers purchased on Ebay):
A pack of 4 M36 flat washers (£5.95, shipping included).
A pack of 10 M30 flat washers (£5.19, shipping included).
A pack of 10 M24 flat washers (£4.19, shipping included).
A pack of 20 M12 penny/repair washers (£2.80, shipping included).
A 7 inch M12 bolt and nut.
A 64mm hole saw (which came in a set of cheapish hole saws that I have).
A bit of very thick plastic pipe, cut to size and placed at the bottom of the bush ears on the axle (to stop them from bending in).

The photo attached shows how I set the washers up, piling them from largest to smallest at both ends of the tool. I used a big pile of M12 repair washers on each end of the tool. An M36 washer will sit quite nicely on the bush at the pushing in end, and the 64mm hole saw makes a perfectly sized bushing receiver. Putting an M36 washer on the hole saw will stop it from collapsing in when you crank the bushing through. To push the bushing out you need to use the M30 washers at the pushing end -- M30 is the same as the diameter of the bush. I had to push mine back out after I realised that I had it in upside down. I don't think that this tool will be strong enough to remove a rusty old bush -- old bush removal is easy enough using a drill on what's left of the rubber, then collapsing the metal part with a hammer and chisel.

Hopefully the photo is detailed enough to see what I did. The photo certainly makes the underside of my 240 look like a rusted old hulk, but it's actually all pretty solid.

I hope this is a useful alternative TAB replacement option.

David


LINK to original thread
Attached Images
File Type: jpg TAB tool.jpg (294.5 KB, 83 views)
__________________
Present: 1990 240GL saloon, 1992 240 estate
Past: 1988 240GL; 1971 144DL; 1972 145DL

Last edited by cumbrianmale; May 29th, 2011 at 11:28.
DW42 is offline  
 


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 01:58.


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.