|
Diesel Engines A forum dedicated to diesel engines fitted to Volvo cars. See the first post in this forum for a list of the diesel engines. |
Information |
|
D5252t crank sprocket later round keyway helpViews : 1448 Replies : 12Users Viewing This Thread : |
|
Thread Tools | Display Modes |
|
Apr 10th, 2021, 05:48 | #1 |
New Member
Last Online: Yesterday 09:07
Join Date: Apr 2021
Location: Christchurch
|
D5252t crank sprocket later round keyway help
I would be grateful if someone knowledgeable with D5252t can help
I am trying to redirect a v70 2.5d from getting scrapped, I bought it not going a risky idea. The cambelt had been done 5000 kms prior and car “just stopped” On taking off cambelt I see it has had trauma and tensioner I also has some rub on engine side, No apparent damage to tappets I found keyway sheared off crankshaft sprocket, I have purchased a new sprocket only to discover inbuilt key is square but my engine is round keyway. I cannot find part number for this or anything online even, except for 1 post here stating there was a change in later management cars 1999- to round type. Nowhere in trawling internet can I find any record of this later sprocket design. Does anyone have one know of part number or any way to obtain one 2nd hand or new? |
Apr 10th, 2021, 09:09 | #2 |
Premier Member
Last Online: Yesterday 13:48
Join Date: Dec 2002
Location: Co. Limerick, Ireland
|
A lot of parts are now NLA (no longer available) from Volvo so it can sometimes be more fruitful to search for VW T4 engine components seeing as it's a VAG unit...
https://www.brickwerks.co.uk/t4-part...cyl-96-on.html I hope the crankshaft keyway isn't damaged and the top end (valves) for that matter. It sounds as though the crank bolt/screw wasn't properly torqued up allowing the damper and sprocket to rattle loose and or someone failed to fit the diamond coated washer (see pdf).
__________________
Liam... '96 854 TDI SE, '99 V70 2.5D S, '05 C70 2.0T Collection, '05 S80 2.0T SE, '15 V70 D4 SE Lux Nav. |
Apr 10th, 2021, 10:56 | #3 |
New Member
Last Online: Yesterday 09:07
Join Date: Apr 2021
Location: Christchurch
|
Many thanks Liam,
It turns out the brand I bought list the parts incorrectly causing a lot of confusion for me So I did buy correct part even if by chance, but it’s wrong. Yes mine was missing washer I’m afraid. I might have to take head off yet. |
Apr 15th, 2021, 08:46 | #4 |
Master Member
Last Online: Apr 22nd, 2024 06:42
Join Date: Jan 2015
Location: Blackpool
|
Morning , I used these people for my diamond washer & woodruff key .
https://www.heritagepartscentre.com/uk/ The engine is the same as the Audi AEL 5 cylinder ( think that is right ) and was used in the VW T4 vans . Nice people were very helpful and prices very reasonable . From experience of this problem , if the key has sheared , you will be removing the cylinder head & replacing a couple of valves ! . The engine is an interference fit & the pistons will bend the valve heads over . At the very least I would order new crank bolt , woodruff key & crank sprocket and diamond washer ( kid you not ) The washer is most certainly required to stop any slippage / movement of sprocket & damper on crank . The bolt you wind up to 120Lbft & then turn through a further 180° and that takes a lot of doing . If it has not got the washer or been tightened fully , you end up back at your starting point hope this helps
__________________
To stupidity & beyond |
Apr 24th, 2021, 12:25 | #5 |
New Member
Last Online: Yesterday 09:07
Join Date: Apr 2021
Location: Christchurch
|
Thanks for help guys,
Finally got right parts but verified what I found earlier which was Engine was out of time but turned over fine, camshaft needed to go couple of teeth, when I tried to do this but it won’t allow me - guess it’s valve hitting on number 4 Cylinder as that is only other piston high with no1 at tdc and have valves down. I can’t understand why it turns over fine slightly out of time, but won’t get in time - surely that would give more valve clearance? Maybe valve head in bad way sticking down next step is taking head off do you agree? Another thing I have a manual and the flywheel marking is not how I see all over internet, I don’t have small notch but further back I have a partially drilled hole is that correct for tdc? Last edited by Juba; Apr 24th, 2021 at 12:27. Reason: Add photo |
Apr 24th, 2021, 21:13 | #6 |
New Member
Last Online: Yesterday 09:07
Join Date: Apr 2021
Location: Christchurch
|
Ok trying to understand fully before I take head off, if someone can concur with me all good
This is with no1 at tdc. Valves closed. Only other piston high is no4 (288degs rotation?) I assume that because it only turns over with cam timing slightly retarded (can not advance to be correctly “timed”)then it must be an inlet valve that is damaged protruding down, the rate at which the valve descends when I try to rotate the cam must bring it into contact with piston. I assume it’s not the exhaust valve as this is coming to it’s seat at this point as I advance. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|