|
x40 S1 Articles Article posts pertaining to x40 S1 Articles series Volvos |
Information |
|
Replacing the Fuel Pump/Sender UnitViews : 31914 Replies : 25Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Apr 29th, 2012, 01:09 | #1 |
Premier Member
Last Online: Nov 15th, 2022 22:34
Join Date: Apr 2010
Location: London / Essex
|
Replacing the Fuel Pump/Sender Unit
This guide applies to all S40 and V40 from 1996 to 2004. The fuel pump sender unit might look different on the Phase 1 cars (1996-2000). The 1.9D, 1.9TD and 1.8 GDI S40 and V40 don't have the pump in the sender unit and instead use the high pressure pumps in the engine compartment. I have also attached in the bottom the VADIS instructions for this job, so have a read through them too if you want. First of all you need to disconnect the car battery, as fuel is highly flammable. Make sure you have the Radio code for your stereo when disconnecting the battery. Avoid smoking or anything that may cause any sparks and make sure you have the rear doors or windows open for ventilation. Fuel fumes may smell nice and give you a high, but they are not good for you.... You now need to remove the rear seats. Lift the bases up and undo these 4 bolts and remove the seats out of the way Then lift the carpet carefully and move it aside tucking the edges in the footwell areas so it stays there. Undo the four screws securing this top metal cover and remove it You will now see another metal cover which seems to offer some extra protection and hold the pump/fuel deposit secured (only guessing here). Just lift it up and out of the way. You might need a screwdriver to lever it out, but most times it should just come out. Now you can see the top of the fuel pump. Use a marker pen and mark a small line or dot where the pump body is in relation to the metal car body (Many thanks to Keith (960kg) for pointing this out to me) Now you need to unclip the top connector which powers the fuel pump. Then you need to carefully remove the fuel line connectors. NOTE the connections for the fuel lines to avoid confusion when you are putting everything bck together. To remove the fuel lines you need to push in these two clips as seen in the next photo (one is red and other is black) and pull out the fuel lines. Make sure you have some sort of cloth or kitchen towels handy, as there will be a tiny bit of fuel spillage when disconnecting the fuel lines. Move the fuel lines and power cable aside (I personally found it easier to tuck them under). You now need to remove the black ring/plastic nut/top cover securing the fuel pump to the tank. There is a special Volvo tool (9995622) for this which I don't have. I personally used a blunt large flat blade screwdriver (or a piece of wood) (positioned at the tip of the green arrow) and used a mallet to gently push the ring anticlockwise. After a few knocks (1-2 turns of the ring, you should be able to turn it by hand (both hands) and unscrew it. Remove the black ring out of the way and lift up the fuel pump unit carefully, so you don't bend the metal rod of the floater. I found that after I raised the pump unit a couple of inches, I tilted it a bit forward and wiggled it out. JOB DONE!!! When you want to put the pump back in, I found it easier to place the rubber seal around the fuel pump unit on the opening of the fuel tank and then push in the fuel pump unit in (see green arrow). Tighten the black ring to 50Nm And a few more photos of the fuel pump sender unit Close-up photo of potentiometer / fuel level sensor. If your fuel gauge is reading the fuel level incorrectly, give the contacts a good wipe to clean them Hopes this helps some people and please take care when following this guide.
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
Last edited by gatos; Apr 29th, 2012 at 01:54. |
The Following 42 Users Say Thank You to gatos For This Useful Post: | -chris-, 40s, 960kg, andy_d, atonap, Awic, Baffler, bar72, barmandani, Biotoxic, caiw123, Chipsnbeer, coughlanc, dcNiko, Dean1985, donaldcurrie, DrDeAtH, druid, DWM, gloster_man, HAPPY ANGLER, littleflower, mechakev, migrator, Mike Stephenson, msanibal, neanderthal, Recognized, rexer12, S40 T4 LPG, sarumboy, Syked69, The Improver, Thingumeebob, tommy t4, tt82, twilightflyer, V40 owner 12, Viggen, Volvo2002, ww1dm1, yusaf1 |
Apr 29th, 2012, 02:33 | #3 |
Premier Member
Last Online: Nov 15th, 2022 22:34
Join Date: Apr 2010
Location: London / Essex
|
Nope. That's exactly how it was. I only wiped the top part which is exposed to the outside. This pump and the guide itself is actually from Siamblue's previous T4
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
|
Apr 29th, 2012, 17:40 | #5 |
Senior Member
Last Online: Jun 4th, 2019 17:53
Join Date: Dec 2011
Location: Bristol
|
Unit from Russia...There is one huge problem to find good quality fuel... |
Apr 29th, 2012, 17:56 | #6 |
Premier Member
Last Online: Nov 15th, 2022 22:34
Join Date: Apr 2010
Location: London / Essex
|
Wtf??? I am surprised that thing is even working. You know you can remove that filter at the bottom and clean it inside.
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
|
Apr 29th, 2012, 20:29 | #7 |
Member
|
bookmarked alex ;o)
|
Apr 29th, 2012, 20:33 | #8 |
Premier Member
Last Online: Nov 15th, 2022 22:34
Join Date: Apr 2010
Location: London / Essex
|
. All my guides are here: http://www.volvoforums.org.uk/blog.php?b=846
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
|
The Following User Says Thank You to gatos For This Useful Post: |
Jun 23rd, 2012, 15:15 | #9 |
Forum Support Team
Last Online: Sep 16th, 2024 07:34
Join Date: Jan 2009
Location: Here.... obviously!
|
After a few months of having no fuel in my car, I now have a working guage again. Yeah.
Cheers for the guide Alex. |
The Following User Says Thank You to tt82 For This Useful Post: |
Jul 7th, 2012, 22:32 | #10 |
Master Member
Last Online: Jul 5th, 2022 20:38
Join Date: Jan 2009
Location: York
|
Great guide, may I add a tip?
Check the condition of the cables from the fuel reading potentiometer and the top of the pump. The up and down motion can cause the cable to break. A multimeter is great for checking this kind of stuff out. A quick solder fixed mine (my gauge was showing empty).
__________________
'04 s60 d5 se. Brrruuuummm etc Last edited by mechakev; Jul 7th, 2012 at 22:37. |
The Following 4 Users Say Thank You to mechakev For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|