|
200 Series General Forum for the Volvo 240 and 260 cars |
Information |
|
240 GL Driver Door HingeViews : 519 Replies : 4Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Oct 24th, 2023, 20:48 | #1 |
Junior Member
Last Online: Mar 8th, 2024 17:09
Join Date: Sep 2010
Location: Ashtead, Surrey
|
240 GL Driver Door Hinge
Good Evening All,
On Sunday I went out to do a particular job on my 240 GL, and quickly ended up dealing with another unknown issue altogether!!! I'm sure you have all been there! I discovered a large amount of rust behind the glued on card panel to cover the driver door hinges (see photograph). I am hoping that this is just confined to the lower tie piece of metal below the hinge itself, but cannot be sure. I did remove the three bolts from the hinge (once I had supported the door!) and the triangular plate also became free. The bolts in turn go into a square plate which in turn go through the panel into the hinge. I would like to remove the square plate so I can clean behind it, but it won't shift......does anyone know if this is actually welded on, or in this case rusted on???!!! Also, would anyone have advice on how critical the lower tie bar across the hinge channel is....this has pretty much disintegrated, and I don't have any welding facilities/equipment. As always, any knowledgeable advice would be greatly appreciated! Best regards, Charles. |
Oct 25th, 2023, 18:22 | #2 |
Premier Member
Last Online: Today 11:06
Join Date: Sep 2017
Location: STANDISH LANCASHIRE
|
The rusty plates mentioned are welded to the "A" post:~
The cars being well engineered will survive one being damaged in this area providing the main structure isn't adversely affected. I would clean the area as best you can to make sure that the existing rust is treated: phosphoric based treatments are good and then paint. After the above is done coat this area with a wax preventative (do both sides of the car as you may have the same problem) The likely cause is a leaking windscreen (see previous posts relating to the two hidden drain holes) this design allows water to run/drip behind the screen and then onto a body lip/structure that moves water behind the card trim panels: normally sealed with Dum Dum mastic so most travels into the "A" post unseen. Once the above is completed keep a check on it- not a lot can be done from under the dashboard but when the screen is wet you may see water tracking towards the post area- the two drain holes are better plugged when the screen is removed. Hope it helps. Bob. |
The Following User Says Thank You to Bob Meadows For This Useful Post: |
Oct 26th, 2023, 09:40 | #3 | |
Junior Member
Last Online: Mar 8th, 2024 17:09
Join Date: Sep 2010
Location: Ashtead, Surrey
|
Quote:
The very first thing I did at the start of this project was to clean out the sills via a hose taped to a vacuum cleaner through the interior holes sealed with the plastic bungs.......a great tip recommended by another user, Nick Lewin,,,,all sorts of debris came out that had collected over the years. I noticed that there is a hole at the bottom of the door hinge channel to allow water to fall through to the sill, which had become blocked due to the rust fragments. |
|
The Following User Says Thank You to crcowley For This Useful Post: |
Oct 26th, 2023, 10:18 | #4 |
Premier Member
Last Online: Today 11:06
Join Date: Sep 2017
Location: STANDISH LANCASHIRE
|
Hi Charles:~
Quite a strange design I think and one that needs to be serviced from time to time. Cleaning the debris out from the inner sills is always worthwhile- check the drain holes as well along the full length of the sill. Once done spray the inside of sills with a wax treatment, fronts and back are the venerable points. (Diluting wax with clean engine oil helps it creep) A further point on the "A" post is checking that your wiring boot/grommet is sealing properly, a smallish through bolt for the dashboard can be seen here and again worth checking no water can enter the posts etc. Good luck. Regards Bob. |
Oct 26th, 2023, 12:33 | #5 | |
Junior Member
Last Online: Mar 8th, 2024 17:09
Join Date: Sep 2010
Location: Ashtead, Surrey
|
Quote:
|
|
The Following User Says Thank You to crcowley For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|