Volvo Community Forum. The Forums of the Volvo Owners Club

Forum Rules Volvo Owners Club About VOC Volvo Gallery Links Volvo History Volvo Press
Go Back   Volvo Owners Club Forum > "Technical Topics" > PV, 120 (Amazon), 1800 General

Notices

PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars

Information
  • VOC Members: There is no login facility using your VOC membership number or the details from page 3 of the club magazine. You need to register in the normal way
  • AOL Customers: Make sure you check the 'Remember me' check box otherwise the AOL system may log you out during the session. This is a known issue with AOL.
  • AOL, Yahoo and Plus.net users. Forum owners such as us are finding that AOL, Yahoo and Plus.net are blocking a lot of email generated from forums. This may mean your registration activation and other emails will not get to you, or they may appear in your spam mailbox

Thread Informations

123GT--handbrake cable after rear end swap

Views : 1075

Replies : 11

Users Viewing This Thread :  

Reply
 
Thread Tools Display Modes
Old May 13th, 2021, 10:15   #1
dcthompson
Junior Member
 

Last Online: May 18th, 2021 00:32
Join Date: Nov 2015
Location: Ann Arbor
Default 123GT--handbrake cable after rear end swap

I am nearing completion of a 100% restoration of my 123GT. I have made some discrete improvements along the way, including replacing the original rear end assembly with one from an 1800ES. My handbrake cable is now too short. Can anyone tell me whether the cable from a different Volvo (e.g. an E or ES) will fit? If I can't find something I will simply have to weld extensions onto the original cable. Has anyone out there performed this modification?
dcthompson is offline   Reply With Quote
Old May 14th, 2021, 15:45   #2
Quarterless
Master Member
 
Quarterless's Avatar
 

Last Online: Jan 3rd, 2024 20:13
Join Date: Mar 2008
Location: Essex
Default

https://speedycables.com/heavy-duty-cables/
These guys could make a new one.
Quarterless is offline   Reply With Quote
Old May 14th, 2021, 17:52   #3
Derek UK
VOC Member
 
Derek UK's Avatar
 

Last Online: Yesterday 14:34
Join Date: Jul 2006
Location: Chatham
Default

123GT had drums. ES has discs. Therefore different cables.
Derek UK is offline   Reply With Quote
The Following 2 Users Say Thank You to Derek UK For This Useful Post:
Old May 15th, 2021, 08:13   #4
dcthompson
Junior Member
 

Last Online: May 18th, 2021 00:32
Join Date: Nov 2015
Location: Ann Arbor
Default Thank you, Derek and Quarterless

Derek and Quarterless: Aside from the differences in the required length of the cable, are there any insurmountable obstacles to making the handbrake function with ES brakes? The subject vehicle is not close at hand at the moment, and I don't recall the details of the ends of the cables where they attach to the ES brakes. A sketch, or better yet a picture, would be very helpful. Dan

P.S. Yes, I know that the ES rear brakes are disks, and the 123GT uses drums. Why did you think I swapped?

Last edited by dcthompson; May 15th, 2021 at 08:15. Reason: clarification
dcthompson is offline   Reply With Quote
Old May 15th, 2021, 13:15   #5
Derek UK
VOC Member
 
Derek UK's Avatar
 

Last Online: Yesterday 14:34
Join Date: Jul 2006
Location: Chatham
Default

IMO, swapping to get rear discs doesn't gain you much even if you are racing the car. For even hard road driving, there is no advantage if your standard brakes are set up well and are in good condition. An extra big negative is that the disc axle takes wheels with a different PCD. Yes you can do a lot of parts swapping at the front to fit the later hubs with matching PCD but it's not just a bolt on. If doing that you might as well go the whole hog and swap to dual circuit brakes. I'd rather not have to carry 2 spare wheels.
Ref the cables, I'm guessing that you might be able to reposition the brackets, or make new ones, where the single front cable meets the yoke for the 2 seperate ones. You will need to use the disc axle cables.
Derek UK is offline   Reply With Quote
The Following User Says Thank You to Derek UK For This Useful Post:
Old May 15th, 2021, 14:23   #6
Vintagewrench
Member
 
Vintagewrench's Avatar
 

Last Online: Nov 11th, 2023 14:34
Join Date: Jul 2016
Location: Brattleboro, VT
Default

Derek, you are correct about the swap not being needed for regular use. However one of the most important reasons to do this swap for racing, rally or hi-performance use is safety and extra strength that comes from the use of bigger diameter, safer, one-piece flanged axles and wheel bearings used on 1800E/ES and 140 series vehicles. Re-drilling the axle flanges to the earlier 5 x 4.5" bolt pattern eliminates having mis-matched wheels and can often be done by drive axle specialists at a reasonable cost.

The original tapered and keyed axles can and do break under hard use, and racing, with the resulting loss of a wheel and tire and the brakes (wheel cylinder pistons can pop out or leak). Breakage is usually followed by a crash or often a roll over caused by the axle housing minus a wheel and brake drum digging into the track or earth.

Back in the day racers were forced to replace the early axles after 5 or 10 races and and usually had them crack tested in-between races. A number of cars were damaged or wrecked and drivers injured due to broken tapered and keyed axles.

One other benefit is axle, bearing, and brake repairs and service takes much less time because of not having to deal with the axle nut, and a puller to get the hub and drum off.

Volvo actually had the disc brake axle homologated with the FIA in 1969 for the Amazon so it could be used in completion.

Last edited by Vintagewrench; May 15th, 2021 at 14:43.
Vintagewrench is offline   Reply With Quote
Old May 16th, 2021, 02:22   #7
Derek UK
VOC Member
 
Derek UK's Avatar
 

Last Online: Yesterday 14:34
Join Date: Jul 2006
Location: Chatham
Default

Higher quality and much stronger axles are available as direct replacements that go a long way to reduce any breakages that might occur. Rallying would benefit most from fitting those. Redrilling the flanges back to the early PCD would, I think, severely compromise their strength in that area. I think they usually break where the spline meets the plain shaft? I've never actually seen one. Point taken about slightly easier servicing but that is more useful for competition where those with ocd might take everything apart after each event or at least with some regularity. Now days brakes are lucky to get checked every 10k miles. Normally if it ain't broke, don't fix it!
Derek UK is offline   Reply With Quote
Old May 16th, 2021, 09:03   #8
dcthompson
Junior Member
 

Last Online: May 18th, 2021 00:32
Join Date: Nov 2015
Location: Ann Arbor
Default

I went with disks for a host of reasons, but in the end it came down to one thing: I prefer them. I like their look. I like never having to adjust them. But there are more advantages to swapping rear ends with an ES than just the brakes; the entire rear end assembly is stronger, the differential is compatible with a multitude of ratios, and a variety of limited slip systems are readily available. The change in rear wheel bolt patterns? Exchanging with the front brakes from an ES is trivially easy. I was only hoping to find someone who has made the same swap to give me some advice on the best way to activate the handbrake.
dcthompson is offline   Reply With Quote
Old May 16th, 2021, 10:32   #9
Underdrive
Senior Member
 

Last Online: Feb 25th, 2024 19:57
Join Date: Jan 2014
Location: stranraer
Default

Quote:
Originally Posted by dcthompson View Post
I went with disks for a host of reasons, but in the end it came down to one thing: I prefer them. I like their look. I like never having to adjust them. But there are more advantages to swapping rear ends with an ES than just the brakes; the entire rear end assembly is stronger, the differential is compatible with a multitude of ratios, and a variety of limited slip systems are readily available. The change in rear wheel bolt patterns? Exchanging with the front brakes from an ES is trivially easy. I was only hoping to find someone who has made the same swap to give me some advice on the best way to activate the handbrake.
On the subject of the handbrake which seems to be your main concern, you not having to adjust them may appeal but you might find the handbrake(which is a drum) inferior to the original drum and in need of regular adjustment and occassional cleaning out. This is something I have found on my 145 with the same system. The lack of handbrake performance is inevitable due to the smaller diameter and only just adequate when working perfectly, just like most modern FWD cars with rear discs.
Underdrive is offline   Reply With Quote
Old May 16th, 2021, 12:45   #10
saintlyvolvo
Junior Member
 

Last Online: Mar 26th, 2024 14:02
Join Date: Jul 2010
Location: Moss
Default

I did this many years ago, and the handbrake solution is very easy. You need these parts: handbrake cable from 1800 70-73, and the pullrod (680913) and the retainer (680909) from either a later 1800 or a 140. Bolt on!
__________________
Front wheel drive is for girls
saintlyvolvo is offline   Reply With Quote
The Following 2 Users Say Thank You to saintlyvolvo For This Useful Post:
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 10:32.


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.