|
PV, 120 (Amazon), 1800 General Forum for the Volvo PV, 120 and 1800 cars |
Information |
|
I've never had so much trouble with SUs before, please help!Views : 5220 Replies : 42Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Jul 20th, 2022, 12:36 | #1 |
New Member
Last Online: Apr 29th, 2023 11:23
Join Date: Mar 2017
Location: Rochester, NY
|
I've never had so much trouble with SUs before, please help!
Okay, so I completely built a new engine for my Volvo Amazon based on the B20 engine I have in my 1800S. Other than the Penta sourced B20 block, they are more or less identical builds. This is a combination that has served me well in the past, so I'm totally befuddled as to why I'm not getting good results:
Volvo Penta AQ130 (B20). This was a freshwater engine in healthy condition that I converted to street use. It had a rebuild one year prior to my ownership. Head was shaved for 10.5:1 Compression B20B headgasket Isky VV71 camshaft Isky high rev lifter kit IPD HD oil pump OEM Pierburg mechanical fuel pump Timing gears checked. Timing checked with a strobe: currently set at 10BTDC idle (800 RPM), 34BTDC at 3,000 RPM Valve lash set to .017 hot. Compression was tested, all of the cylinders were around 170PSI, give or take 2lbs each. SU HS6 carbs, completely rebuilt with new springs, dampers, throttle shafts, gaskets, floats, jets, etc. I am using KD needles and MMO for dashpot oil like I always have in all my SU carbs. Chokes are set and fully functional. Linkage checked and has full extension, it doesn't bind. Throttle will open completely and does not bind. Dashpots rise and fall at the same rate. Carbs were balanced independently and verified with a traditional Unisyn. No air leaks or excessive PCV pressure. I am using the same Bosch mechanical advance distributor as my 1800, with Pertronix ignition. NGK straight copper plugs with IPD silicone leads. Resurfaced flywheel, new clutch and pressure plate, M41 in tip top condition. New AGM battery, new Bosch blue coil. I have a fresh tank of 93 Octane (AKI). My problem is that at 4,000RPM, it's like my car hits a wall and won't accelerate any further. Adjusting timing, mixture, etc, I still seem to hit this artificial wall at 4,000RPM. In any gear? 4,000RPM. Neutral? 4,000RPM. Slow application of throttle? 4,000RPM. Even if I pull the choke at 4,000RPM, it still won't go beyond. I swapped out the distributor with an identical one set up for points, the wall was now at 3,500RPM. I replaced it with the Pertronix setup and I was again at the 4,000RPM wall. It seems like nothing I have done will get me past this wall. It revs up fine and feels completely normal, then just stops at 4K. It's very unusual. The 123GT tachometer is within spec, so this isn't a false reading. Foot on the throttle or even disconnecting the linkage and moving it by hand, no change. I thought about buying a Gunson Colortune to check if it's running lean or rich, but they are all out of the 14mm size I need and I cannot find them on the secondhand market. The only thing I can think about is adding a wideband air/fuel meter and measuring it with an O2 sensor, but I don't have money for that right now. With my previous B20 build in the 1800, I have no trouble getting up to 7,000RPM, and it still pulls really hard around 5,000RPM. Your ideas and advice are appreciated, thanks in advance! |
Jul 20th, 2022, 13:21 | #2 |
Member
Last Online: Today 08:37
Join Date: Oct 2018
Location: North of Jedburgh
|
A friend had a similar problem (wasn't a Volvo) which turned out to be a partially blocked exhaust.......was a fuel injected engine.
It wouldn't even rev up passed 5k when stationary, split the exhaust at front pipe and away she went. Maybe worth checking?
__________________
V70 2.4 Phase 1.....2435cc.....Registered 31/3/2000.....Leather,AC,CC,etc!.....182k |
Jul 20th, 2022, 13:57 | #3 |
New Member
Last Online: Apr 29th, 2023 11:23
Join Date: Mar 2017
Location: Rochester, NY
|
Thanks for the tip. The exhaust is recent production exhaust from VP Autoparts or CVR, I forget. I am using a B20 cast iron manifold with a 2-1 downpipe. I'll see if disconnecting it after the downpipe makes a difference, I know they have some less restrictive sport models available that could improve breathing.
|
Jul 20th, 2022, 14:27 | #4 |
Master Member
Last Online: Mar 14th, 2024 17:23
Join Date: Jun 2009
Location: Milton Keynes
|
This sounds to me like your electronic ignition.
I am not familiar with the one you have but, I had a similar issue with my 123 Tune ignition when first fitted. My car was limited to 5000 rpm. With assistance from the manufacturer's help line my car will now run to 7000rpm. |
Jul 20th, 2022, 14:33 | #5 |
Premier Member
Last Online: Today 12:21
Join Date: Jul 2007
Location: Connecticut, USA
|
Bork;
First, compliments on a very complete listing of the preconditions, although some are not likely to affect the ability to rev past 4K... Also, your title might be a bit on the presumptuous side...I don't think you can point the finger of suspicion squarely at the SUs just yet... Ignition is one of the first things which is likely to hold back the revs, but with idle and advance checked and apparently right, I would move on to what BV, also mentioned, and the second thing I thought of: Breathing...I presume you are doing your initial tuning and checks without Air Filters installed, so it can't be blocked AFs...so what's left is the Exhaust Sys...I'd disconnect and make a road test run with an open sys ...preferably not down your own residential neighborhood! By "Dashpots rise and fall at the same rate." I presume you mean between the two carbs, not for each carb...Dashpot Rise must be dampened, but Fall must not! Also, are you doing your tests only in the driveway (not road/under load), in which case I must ask if your initial mixture setting after carb rebuild was at 12 faces down on the Jets? I don't know this for certain, having never done this, but if, for instance, you could get the engine started with them flush at the Venturis (with the help of ether I suppose), the engine might be able to be reved against its own inertia, but it would clearly be very lean (and not so good for it!), but it wouldn't be able to make much power against a full load, and I wonder where it would "run out of breath"... Good Hunting! |
Jul 20th, 2022, 15:23 | #6 |
Chief Bodger
Last Online: Today 10:28
Join Date: Oct 2009
Location: Aberdeen
|
Çheck the timing at 4000rpm. How old is the coil?
If a fuel delivery issue things to check; fuel pump, bowls float correct height, no holes in floats and carb fuel intake valve operational.
__________________
One day I will get rid of all of the rust. |
Jul 20th, 2022, 15:25 | #7 |
Chief Bodger
Last Online: Today 10:28
Join Date: Oct 2009
Location: Aberdeen
|
As per Ron's suggestion, how did you set the fuel mixture? A O2 wideband sensor and gauge will help check what it is at higher revs when driving.
__________________
One day I will get rid of all of the rust. |
Jul 20th, 2022, 15:51 | #8 | |
New Member
Last Online: Apr 29th, 2023 11:23
Join Date: Mar 2017
Location: Rochester, NY
|
Quote:
Yes, when compared to one another, if I push them up at the same time, they have the same amount of resistance and they fall together when I release them. My initial setting was at 12 flats, but I believe they are currently sitting at 14 flats. That's right about where they were when I set up my 1800S with the identical engine and carb setup. The air cleaners are currently off, but I have a set of CNC machined aluminum velocity stacks that allow me to quickly remove a modern conical air cleaner for carb service. Removing the velocity stacks makes no change in behavior. (For those interested, these velocity stacks were made by namvet6970 on eBay.) |
|
The Following User Says Thank You to Bork Volvo For This Useful Post: |
Jul 20th, 2022, 16:02 | #9 | |
New Member
Last Online: Apr 29th, 2023 11:23
Join Date: Mar 2017
Location: Rochester, NY
|
Quote:
The coil is about one year old, it is a Brazilian made Bosch Blue coil which passes the "four tests" outlined here: https://www.ratwell.com/technical/BlueCoil.html I will check the timing at 4k when I get home. The bowls have new black floats from Joe Curto, and the viton needle valves are new and appear to be operational. When holding the lids upside down, they are set to 1/8" using a drill bit. I used the method outlined here: https://www.sw-em.com/SU%20Carb%20Se...uelbowl_Floats |
|
The Following User Says Thank You to Bork Volvo For This Useful Post: |
Jul 20th, 2022, 16:15 | #10 | |
New Member
Last Online: Apr 29th, 2023 11:23
Join Date: Mar 2017
Location: Rochester, NY
|
Quote:
I thought that was the case at first, so I tried to rule it out by installing a stock points ignition with new cap, rotor, condenser, and points, but it actually reduced max RPM at WOT to 3,500. FWIW, my 1800S has the same exact Pertronix and coil setup and it was totally plug and play. I am very interested in a 123 ignition because I have only heard great things, but I cannot afford one right now. |
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|