|
S40 / V40 '96-'04 General Forum for the Volvo S40 and V40 (Classic) Series from 1995-2004. |
Information |
|
V40, Rear brake linesViews : 693 Replies : 7Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Aug 8th, 2021, 13:46 | #1 |
New Member
Last Online: Sep 14th, 2021 11:41
Join Date: Mar 2019
Location: HASTINGS
|
V40, Rear brake lines
Hi, next week end, I'm going to finally change my rear brake lines,
I have all the kit to make up the new lines, What i was wondering is, does the tank have to be removed to get at the passenger side line, or can it just be allowed to drop down with hoses still attached just enough to free the brake pipe from the clips ? |
Aug 8th, 2021, 13:55 | #2 | |
Premier Member
Last Online: Nov 15th, 2022 21:34
Join Date: Apr 2010
Location: London / Essex
|
Quote:
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
|
|
Aug 8th, 2021, 14:01 | #3 |
New Member
Last Online: Sep 14th, 2021 11:41
Join Date: Mar 2019
Location: HASTINGS
|
The pipe was an advisory on the last MOT, its ok, apart from on the drivers side near the flexible where the pipe has corroded. On both sides, i can drop down that pipe without dropping the tank, but as I'm going to replace the whole pipe, and replace with new, it makes sence to do both, the passenger side is going to be the problem, as the line runs under the fuel tank, or very close to it
|
Aug 8th, 2021, 14:12 | #4 | |
Premier Member
Last Online: Nov 15th, 2022 21:34
Join Date: Apr 2010
Location: London / Essex
|
Quote:
At the same time, if you are replacing the entire lines, then you might as well don't properly and remove the tank too, so you can then route the new brake lines the proper original way
__________________
Current car: 2002 S40 1.9D, 1992 240SE Nullius in Verba
|
|
Aug 8th, 2021, 18:17 | #5 |
VOC Member
Last Online: Yesterday 21:51
Join Date: Mar 2008
Location: Northampton
|
To do the job properly the tank needs dropping. It is also an opportunity to check the floorpan above the tank for corrosion - there is no rust protection applied apart from the phosphate primer. The rear pipes are joined at the bottom of the bulkhead just above the front suspension. Attachment shows work in progress on my V40.
__________________
2001 V40 2.0lt Sport lux - Daily Driver. 174k miles. 2003 C70 2.4 GT Convertible - Garage Queen. 65k miles. http://www.neptuno6benagil.com |
The Following 2 Users Say Thank You to ITSv40 For This Useful Post: |
Aug 12th, 2021, 13:59 | #6 |
New Member
Last Online: Sep 14th, 2021 11:41
Join Date: Mar 2019
Location: HASTINGS
|
Its really being a PITA got the car up on stands so i can get underneath safely, thought i would start with passenger side, the bolts came out easily, that hold the brake pipes to the floor, the rear brake union is mullered, ive got the proper union spanner, but its to far chewed, by a previous owner, so I'm going to have to cut that,there a bolt right to the tank, that i just can't quite get to, with the tank in situ,so tomorrow im going to see if i can get the tank out and do the whole lot, Next question,how do i get at the front unions, do i undo the top unions, unbolt the joiner, somehow work it down and out because due to the lack of access, i'm scared i might round off the bottom unions if i try to undo them in situ.
|
Aug 12th, 2021, 14:43 | #7 |
VOC Member
Last Online: Yesterday 21:51
Join Date: Mar 2008
Location: Northampton
|
It is a few years since I did mine so memory fades a bit. I only undid the lower unions from the joiner to remove the rear pipes. I think? I found it easier to reach down from above to undo and then fed the pipe out from underneath. Same with refitting- feed pipe into position from underneath and then locate and tighten union from above. I also made up some blanking plugs by filling a couple of union nuts with solder to seal the front part of the system so that air did not get in the abs module. I managed to get the old pipes out in one piece and bent the new Kunifer pipes to suit before fitting to the car. They just then needed a little tweeking to get them to look neat and tidy.
__________________
2001 V40 2.0lt Sport lux - Daily Driver. 174k miles. 2003 C70 2.4 GT Convertible - Garage Queen. 65k miles. http://www.neptuno6benagil.com |
Aug 13th, 2021, 14:54 | #8 |
New Member
Last Online: Sep 14th, 2021 11:41
Join Date: Mar 2019
Location: HASTINGS
|
Well, its been fighting me every inch of the way, ended up having to cut some sections of pipe, the drivers side literally fell apart where it runs past the tank,, the front unions refused to undo, so I'm going to have to join in the where the first clamp is, and run the new pipe from there, with male/ female connectors except that bloke sod, screwed me again, i have not got any female unions.
|
The Following User Says Thank You to martin 56 For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|