|
XC90 '02–'15 General Forum for the P2-platform XC90 model |
Information |
|
"Anti skid temporarily switched off" warning on- xc90Views : 10039 Replies : 9Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Dec 22nd, 2010, 16:16 | #1 |
New Member
Last Online: Dec 24th, 2010 07:58
Join Date: Dec 2010
Location: Henley on Thames
|
"Anti skid temporarily switched off" warning on- xc90
Hope someone can help! I've had the above warning for past three days, have had front disc pads changed at local garage but they have advised I need to go to a volvo dealership to resolve the issue.
Contacted volvo dealership who can't fit me in until 30th Dec but have told me over phone that there is no traction at present! Small challenge - driving to France on 26th December! Can anyone advise me what I could check on the car to try to resolve myself? Thank you in advance |
Dec 22nd, 2010, 16:38 | #2 |
Master Member
Last Online: Dec 16th, 2020 20:33
Join Date: May 2009
Location: kirknewton
|
could be anything from dirty sensor to a broken wire,
you need to start with getting the codes pulled. perhaps some kind chap on here might have a code reader, must be someone not far from you who has one. |
The Following User Says Thank You to kenny For This Useful Post: |
Dec 22nd, 2010, 20:32 | #3 |
Member
Last Online: May 8th, 2023 13:47
Join Date: Jun 2010
Location: Stirling
|
I had the same thing recently on my V70 and they said it required a software upgrade. I wasn't sure why because I hadn't changed anthing but whatever they did it resolved it.
__________________
V90 D4 Inscription-Bright Silver-Geartronic |
Dec 22nd, 2010, 21:27 | #4 |
New Member
Last Online: Feb 12th, 2014 20:19
Join Date: Feb 2009
Location: Northamptonshire
|
anti skid serv. req.
had same problem recently. in a nutshell, look at fuse box in cargo area ref.page191 in handbook fuse no.23 =awd little brown 7;5 amps beieve replaced for 50 pence what a result! so much for dealers wantinglots of money to anylise
|
Dec 22nd, 2010, 21:29 | #5 |
xc90, volvo number five
Last Online: Jun 8th, 2024 23:08
Join Date: Dec 2005
Location: Grappenhall
|
did you get the warning, straight after having the pads changed ?
dave |
Dec 23rd, 2010, 18:45 | #6 |
New Member
Last Online: Dec 24th, 2010 07:58
Join Date: Dec 2010
Location: Henley on Thames
|
No, it came up beforehand but knew pads were due to be changed soon. Warning still on today!
|
Dec 23rd, 2010, 18:46 | #7 |
New Member
Last Online: Dec 24th, 2010 07:58
Join Date: Dec 2010
Location: Henley on Thames
|
Thanks will def try this tomorrow - hope it works!!
|
Dec 23rd, 2010, 19:04 | #8 | |
xc90, volvo number five
Last Online: Jun 8th, 2024 23:08
Join Date: Dec 2005
Location: Grappenhall
|
Quote:
dave |
|
Jan 3rd, 2011, 21:14 | #9 |
New Member
Last Online: Jan 3rd, 2011 21:15
Join Date: Jan 2011
Location: Reading
|
This is normally to do with an ABS sensor.
|
Jan 4th, 2011, 12:12 | #10 |
Member
Last Online: Aug 8th, 2019 23:04
Join Date: May 2009
Location: Glasgow (ish)
|
We had that fault last year... My Sealey code reader showed no fault, but the OBD was adamant that a fault existed... I took the car to a local indie and his code reader showed a fault with the NSF abs sensor... The fault only showed when the car was in motion though, so a quick shuftie was in order... The indie found that the NSF reluctor ring (metal ring with circular inside dia and castellated outer dia) fitted to the NSF outer CV joint was actually cracked (we had an "incident" with a rock on that corner earlier in the year, it made the wheel a very romantic heart shape too..!!).
I figure that the rock actually hit this ring too ' because it was cracked, causing just one of the gaps between the high points of the castellations to be slightly wider than the others... As soon as the car started moving, the sensor detected the uneven pulses and flagged up a fault... The part is available separately at a coat of about £14... I'm told that "excessive" corrosion and debris in the reluctor ring can cause similar problems... It's a PITA to fix, as the drive shaft has to be withdrawn from the wheel bearing in order to get the new ring on, so labour is much higher than parts costs... Cheaper than an ABS sensor or control unit though... '-) Miti |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|