|
x40 S1 Articles Article posts pertaining to x40 S1 Articles series Volvos |
Information |
|
GUIDE : Changing the front gear linkage bushesViews : 16212 Replies : 7Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Aug 28th, 2007, 07:48 | #1 |
Senior Member
Last Online: Oct 20th, 2013 20:24
Join Date: Aug 2007
Location: Derbyshire
|
GUIDE : Changing the front gear linkage bushes
If you are finding your gearbox has become very sloppy and that you have trouble getting into first, second or fifth gear then you might be in need of a gearbox bushing refresh. This guide will take you through which parts to get and how to fit them, it will tighten up the gear shift and hopefully regain that 'as new' feel. Note this guide is for boxes with reverse up and to the left.
Step 1 - We'll start at the front of the linkage (next to the gearbox). You need to buy two plastic bushes and two O rings. The part numbers are : Bushing 30871722 (£1.15 each) O-ring 30872329 (0.25 each) This will set you back £3.29 including VAT Picture 1 shows the back of the bush and an o ring Picture 2 shows the front of the bush where the o ring sits Picture 3 shows the o rings fitted to the bushes (they jus tpush in with your fingers) Picture 4 is the two bushes ready to fit |
Aug 28th, 2007, 07:49 | #2 |
Senior Member
Last Online: Oct 20th, 2013 20:24
Join Date: Aug 2007
Location: Derbyshire
|
Step 2 - I just wanted to show how much play there was in the gearstick, this is in first gear
Step 3 - Slide a jack under the car at a suibtable point i.e. on a structural part of the car as shown Step 4 - Jack the car up nice and high, give yourself plenty of room to work or the job is twice as difficult |
Aug 28th, 2007, 07:50 | #3 |
Senior Member
Last Online: Oct 20th, 2013 20:24
Join Date: Aug 2007
Location: Derbyshire
|
Step 5 - Once the car is jacked up, fit an axle stand underneath in case the jack fails. Again, fit it on a suibtable point such as the member running down the car as shown. Note I always release the jack until the weight sits on the axle stand and then pump the jack once more so the weight is split between the two
Step 6 - Once the car is safely supported, climb under and trace the gearbox linkage (shown in picture 1) to the joint we are interested in (picture 2) Step 7 - Hook an 11mm ring spanner over the top of the assembly and hold it in place. Note you can pull the linkage down to make it easier to fit the spanner on |
Aug 28th, 2007, 07:50 | #4 |
Senior Member
Last Online: Oct 20th, 2013 20:24
Join Date: Aug 2007
Location: Derbyshire
|
Step 8 - Use a socket (or spanner) to remove the 11mm nut from the bottom whilst holding the spanner
Step 9 - Push the bolt up and remove it from the top of the bushing Step 10 - You can now move the linkage from the gear stick backwards and away from the problematic bush |
Aug 28th, 2007, 07:51 | #5 |
Senior Member
Last Online: Oct 20th, 2013 20:24
Join Date: Aug 2007
Location: Derbyshire
|
Step 11 - Remove the old bushing. You have the old version of the two bushes and two o rings that you bought to remove and also a metal tube that goes between them. Simply pull either bush off then the rest will slide out
Step 12 - You can see the old bush was a bit oily and dirty. This picture shows the metal bar that joins the two bushes Step 13 - Here I've tried to show how much play there was in the bush. The metal rod could wiggle up and down in the bushing a small amount which is multiplied a lot by the time it hits the gearstick |
Aug 28th, 2007, 07:52 | #6 |
Senior Member
Last Online: Oct 20th, 2013 20:24
Join Date: Aug 2007
Location: Derbyshire
|
Step 14 - Now give the metal rod a quick wipe and grab your two new bushes to fit (picture 1). Check everything fits together properly as shown in picture 2.
Step 15 - Sorry for the blurry image but you should see I've fitted the top bush and metal rod in place Step 16 - Now squeeze the second bush into place, it shouldn't require much of a squeeze if everything is lined up |
Aug 28th, 2007, 07:53 | #7 |
Senior Member
Last Online: Oct 20th, 2013 20:24
Join Date: Aug 2007
Location: Derbyshire
|
Step 17 - Grab the gear linkage arm and slide it back over the bush (it will be a slightly tight fit)
Step 18 - Try to align the holes with those in the bush as close as you can (don't get too carried away though!). You can see that my car is due a bit of a clean here Step 19 - Use the bolt from the underside as shown in the picture to make sure you get everything in alignment. Whilst pushing the screw up from beneath you can manoeuvre the gear linkage around until it all slides into place Step 20 - Once aligned, drop the bolt in from the top and tighten the 11mm nut on. This is done in the same way as early using the 11mm spanner on the top also |
The Following User Says Thank You to JSeaman For This Useful Post: |
Aug 28th, 2007, 07:53 | #8 |
Senior Member
Last Online: Oct 20th, 2013 20:24
Join Date: Aug 2007
Location: Derbyshire
|
Step 21 - This is to show how much play was left after the front bush was replaced
Hopefully you can see the amount of freeplay was reduced significantly at this stage. I could now get into first and second gear without having to lift the reverse collar so was thoroughly pleased. For me, there is still an unacceptable amount of play in the gearstick so I will do he rear bushes too in another guide (when Volvo finally get the parts!) Note that the kits you can buy on ebay for about £20 have the metal tube in them which is not required. The shoudln't under normal operation, the plastic ends are there to take the brunt of the movement so it is cheaper to just buy the bushes from Volvo directly. |
The Following 24 Users Say Thank You to JSeaman For This Useful Post: |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|