|
C30 / S40 & V50 '04-'12 / C70 '06-'13 General Forum for the P1-platform C30 / S40 / V50 / C70 models |
![]() |
|
CEM related issues: My diary of ongoing findings...Views : 20914 Replies : 73Users Viewing This Thread : |
![]() |
|
Thread Tools | Display Modes |
![]() |
#71 |
New Member
Last Online: Feb 13th, 2024 22:02
Join Date: Jan 2024
Location: Norwalk, CT
|
![]()
Testing reply
|
![]() |
![]() |
![]() |
#72 |
New Member
Last Online: Feb 13th, 2024 22:02
Join Date: Jan 2024
Location: Norwalk, CT
|
![]()
Trying to talk to Clan. Have similar issues w/ 2010 xc 90. Intermittent no start - immobilizer mode along with brake ABS, bad low bulb. Dealer replaced keys along with new antenna ring. This was after battery replacement and new starter - not by dealer. This is when issue first started. After key/antenna ring replacement car worked for two weeks then today wouldn't start. Disconnected battery. Hooked up after 30. Started. Thinking of replacing 6 CAN terminals. Old terminals just pull out of connector housing and new ones are soldered to correct wires?? I saw locations pin numbers on your previous posts. Shrink wrap connections too?? This is for flat white rectangular CEM on passenger side? Green and brown connectors @ bottom and blue on top?? I'm loosing my mind with this issue. Also should I also clean CEM?
|
![]() |
![]() |
![]() |
#73 |
VOC Member
Last Online: Jun 12th, 2024 21:17
Join Date: May 2011
Location: Fife
|
![]()
3yrs after I first posted my tales of woe and subsequently emery clothed and cleaned my CEM pins and it's never once given any further issues... which is quite surprising more do as lately it's been relegated to third car duties and thus at times will only be used once a week and is left sitting in cold, damp conditions. It just clocked over to 240,000 miles last week... it just seems utterly unwilling to give up.
|
![]() |
![]() |
The Following User Says Thank You to Turbodave For This Useful Post: |
![]() |
#74 | |
New Member
Last Online: Jun 9th, 2024 07:57
Join Date: Oct 2019
Location: Wellington
|
![]() Quote:
1. Dashboard no display but car still running 2. wiper motor goes crazy running at highest speed, and not responsive to control lever 3. indicator flashing with no responsive to control lever 4. Engine performance reduced 5. Bliss error 6. central lock not respond neither to key remote or door panel buttons 7. Transmission error car shaking. 8. SRS module error 9. Steering Wheel Module error 10. ABS error DSTC system disabled 11. immobiliser error 12. no crank start 13. accelerate panel error 14. ambient temperature sensor error, shows like -35°C while real temperature is 15°C, and number jumping. it feels like the car is possessed when the wiper goes crazy and all error code and red light on dashboard shows up, this can't be just CAN/LIN connection lose or corrosion, I have tried to clean up the pins several times and no signs of damage on the CEM circuit board when take out from fuse box, the symptom shows 6-8 months after unplug/cleaning the pins. Logically that's not possible the symptoms caused by cable lose or corrosion happens so randomly, it's more like software level problem, like RAM/cache/buffer issue on computer, the CEM build up "electronic errors" overtime and shooting out when errors overflow, so every time when unplug call cables and disconnect battery from CEM, the errors reset and cleaned. the hardware quality is reliable and solid but the software of the V50 is a real pain in the ass. Last edited by willcnz; Jun 7th, 2024 at 06:20. |
|
![]() |
![]() |
![]() |
Tags |
s40 cem fault, v50 cem fault, volvo faulty cem |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|