|
S80 '06-'16 / V70 & XC70 '07-'16 General Forum for the P3-platform S80 and 70-series models |
Information |
|
How to: Manual EPB removal/wind offViews : 19753 Replies : 44Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Sep 22nd, 2019, 18:08 | #41 |
Premier Member
Last Online: Feb 11th, 2023 20:32
Join Date: May 2010
Location: Blyth, Northumberland
|
Re the Volvo Brake Pad Kit. VO31445796
Replaced rear brake pads on daughter's 2011 XC70 a few days ago using the 9volt PP9 battery method to wind the EPB motor back.
I had the car up on axle stands and after loosening the wheel bolts I put the parking brake off. As stated elsewhere care is required to release the catch on the inboard side of the electrical plug when removing it, otherwise it was very easy. Old pads were well worn down, the outer ones to 2.00 mms so motor took a while to wind all the way back. Once motor wound back, opened caliper bleed nipple (previously treated with releasing fluid) and pushed piston back with standard brake piston compressing tool. I had obtained OE pads kit as above from my main dealer. It contained four "spring clips" and four pads. Upon first inspection the four "spring clips" appear identical, but they are not. Two have a thin rubber coating on the side which fits against the caliper bracket and on closer inspection they also have an extra tab. The instruction leaflet points this out and states that these clips must be fitted to the upper part of the caliper bracket. (i.e. the disc is turning towards them ). Okay, understood, BUT The four pads in the kit have two different part numbers on them. Two marked with 32337286 and two marked with 32411312. All four pads appeared physically identical but the friction material on one pair did appear to be slightly different to the material on the other pair. I could not find any reference to this in the instruction leaflet so queried it with the main dealer. The parts assistant produced an identical kit which also had the two different pad part numbers within it. After checking with the service staff he informed me that: Pad part number 32337286 should be fitted on the inboard side of the caliper, i.e. against the piston. Pad part number 32411312 should be fitted on the outboard side of the caliper. He also confirmed that the instruction leaflet does not make any reference to this. Having reassembled the brakes I wound the EPB motor back in by reversing the polarity of the battery leads. After refitting the road wheels and before lowering the car back onto it’s wheels I checked that each motor was operating correctly by applying the brake off and on and checking that the wheels were locked or free to rotate as they should. Well pleased as I had approached this job with some trepidation as never having worked on EPB before but it was a doddle. Ian Last edited by Ian21401; Sep 22nd, 2019 at 19:27. Reason: Add text. |
The Following 2 Users Say Thank You to Ian21401 For This Useful Post: |
Jan 12th, 2020, 21:03 | #42 | ||
Upstanding Member
Last Online: Sep 12th, 2023 11:29
Join Date: Mar 2018
Location: Ludlow
|
After an MOT failure a couple of days ago for excessively worn rear brake pads, I decided to follow this guide. Given that the guide had been originally written around a previous model I was a bit cautious, however it seems that Volvo have carried over that same rear braking system with no changes that were obvious to me! Rather than remove the motor from the caliper I decided to use a PP3 battery applied to the EPB assembly terminals to unwind the mechanism. I would suggest that using anything 'beefier' than this would be a mistake, as the PP3 limited power delivery avoids damaging the motor when it hits it's limit.
Quote:
To unwind the calipers requires the positive connection to be applied to the upper connection of the motor on the driver side (UK RHD car) and the lower connection on the passenger side... I wound until they stopped (took about 15 seconds). Then obviously vice versa to apply the brakes afterwards, which I did to save the car having to do this and possibly getting confused (plus it also made it far easier to tighten the disc retaining screws, as I also had to replace both rear discs). Quote:
The caliper bolts were incredibly tight - probably due to the thread/stud lock used - and the 13mm AF heads had an unusually low profile, resulting in the standard 12-point socket initially slipping off as soon as I applied some serious torque. I was quite worried about this but then discovered that an old 1/2" socket I found was actually a much nicer fit (and was also a 6-point type as an added bonus). A massive thanks to everyone who has contributed to this really useful thread.
__________________
GONE: 2015 V60 D4 181 (VEA) R-Design Lux Nav manual in black Last edited by Zebster; Jan 12th, 2020 at 21:53. |
||
The Following 3 Users Say Thank You to Zebster For This Useful Post: |
Apr 8th, 2020, 15:59 | #43 |
Senior Member
Last Online: Dec 21st, 2022 21:28
Join Date: Mar 2018
Location: Northants
|
My rear pads are down to 3mm and can’t get it replaced at dealership as it’s closed. My local garage is open and showed him this guide.
He is happy to try it so fingers crossed it works as I need the car for work. Just noticed this guide is for V70, hopefully this is the same for my 17 reg S90?
__________________
2017 Volvo S90 D5 PowerPulse AWD Inscription - Xenium Pack, Panoramic Sunroof, Massage Front Seats, Family Pack. Electric Silver Nappa Soft Leather Perforated/Ventilated Charcoal Last edited by JC888; Apr 8th, 2020 at 16:51. |
Jul 17th, 2020, 22:49 | #44 |
New Member
Last Online: Mar 4th, 2024 21:57
Join Date: Jan 2018
Location: West Herefordshire
|
Replaced rear brake pads and discs on 2015 XC70
Hi All,
I wish I had seen this very useful guide before I started the job! I made the mistake of trying to use a copy of VIDA that I had obtained. The advantage I thought would be that the wind back of the caliper would be easier. The VIDA copy worked OK until the car battery voltage dropped. I have not used it much recently due mainly to the Covid-19 pandemic and staying at home. What I learned from doing this work for the first time: 1. The bolts (15mm hexagon screws) for the caliper carrier to the suspension arm are quite tight due to threadlock. 2. The bolts (13mm hexagon screws) for the caliper are also fairly tight due to corrosion and threadlock> 3. New bolts (1 and 2 above) with threadlock on them are included with Volvo supplied pads and discs. 4. I would recommend the manual method for winding the back of the caliper with a torx type tool and then closing up the piston with a g clamp and suitable padding/wood to protect the drive plate. 5. The O ring seal for the motor cost an eye watering £23 + vat from a Volvo dealer. This is ridiculous for a heat resistant O ring and 2 T30 torx screws!! I have actually complained to Volvo UK about this price. In the event the O ring is likely to be reusable, but always handy to have one just in case. 6. All the parts were very well made IMO, and fitted without problems I am getting around 30 000 miles from a set of pads and discs and wondered what sort of mileage others achieve. I perhaps could have left the discs in place as they had not reached the wear limit (19mm) but were noticeably 'lipped'.
__________________
2015 XC70 D4 SE NAV 181 |
Jul 11th, 2023, 17:59 | #45 | |
Junior Member
Last Online: Dec 14th, 2023 12:22
Join Date: Jan 2023
Location: Helston
|
Quote:
I’ve a bucketful of lights on the dash so went for a Foxwell 530 dedicated to Volvo. Seriously miffed that despite offering to put the brake into service mode it hasn’t done it despite three attempts. Given its just a polarity change to advance or retract I get all sorts of stuff that tries to explain but just confuses. I had to buy a cheap windows computer to actually initiate the Foxwell! There’s me thinking I was rid of windows ten years ago and yet its back in the house again. Still not intuitive but a lot better at getting from one end of a task to the other. |
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|