|
200 Series General Forum for the Volvo 240 and 260 cars |
Information |
|
Starter motor swap and refurbishViews : 1678 Replies : 16Users Viewing This Thread : |
|
Thread Tools | Display Modes |
Feb 22nd, 2021, 23:05 | #1 |
New Member
Last Online: Feb 8th, 2024 14:01
Join Date: Dec 2009
Location: Market Drayton
|
Starter motor swap and refurbish
I bought a "new" 240 (1991 Torslanda) just over a year ago (from an ad in Volvo Driver) and have revelled in its responsiveness ever since. 2.0 petrol injection makes it really GO compared with the horribly sluggish 2.3 carb DL which I had run for 24 years.
However - and here I get to the point - over the last couple of months it has needed two people to start it. My wife to hold the ignition key in the start position and me to whack the starter motor solenoid with a lump of wood. Yesterday I got round to doing something about it. I still have the old (1987) 240DL, with a reliable starter, so I drove it up wheel ramps and removed the starter. I got the Torslanda up another pair of wheel ramps (thank you, neighbour), removed the dodgy starter and fitted the one from the DL. Now ... and here is my question ... have I done the right thing? The starter removed from the Torslanda has a slimmer body than the one from the DL. It seemed to bolt in OK, and it started fine, but now I'm worried that if the pinions are different I could damage the flywheel. I have started to dismantle the faulty starter. The three cross-head screws on the solenoid were a pain, but eventually yielded to hammer blows to an impact driver. The next problem is the two 7mm bolts on the starter motor body which are tending to round off. Oh, with the starter off and before doing any dismantling, I earthed the body and touched a battery positive wire to the spade terminal on the solenoid. It operated and flung the pinion out (and, to my surprise, it started to spin slowly). Touching the lead to the lower solenoid terminal, the one connected to the starter itself, the pinion spun strongly. But sounded rather graunchy. I repeated the exercise to find that sometimes there was no spark and the motor did not spin. I can't remember whether the solenoid always operated - I think it didn't. Anyway, the shaft the pinion slides in and out on looked dirty and felt sticky. Trying to push the pinion round with my thumb was quite difficult. I expect, if and when I get the motor apart, I'll find everything caked with dirt and the brushes worn out. Back to the solenoid: when I pulled the body off the armature it all felt a bit sticky. Obviously I can clean the parts, but should I lubricate the armature? Should it slide in and out freely? I would have thought so. I would be grateful for your comments. Thanks. |
The Following User Says Thank You to John Halford For This Useful Post: |
Feb 23rd, 2021, 08:53 | #2 | |
Premier Member
Last Online: Today 10:55
Join Date: May 2012
Location: Lakenheath
|
Quote:
From your description, i would suggest the following. First, the brushes are badly worn. Second the armature is also worn - usually they can be skimmed and undercut to restore them to a usable condition but you'll need a lathe and then lots of patience and a broken hacksaw blade to undercut the comm. Next, the chances are the bushes commonly referred to as D/E and C/E bushes (Drive End and Commutator End) are almost certainly worn, best to renew these. They are a press fit in their brackets and need soaking overnight in clean engine oil before fitting. The solenoid plunger/armature should be clean and slide in and out freely in the solenoid body. The "7mm" nuts may in fact be 1/4" AF but either way, soaking first with penetrating oil should save you a lot of grief - removing the through-bolts with them still fitted is near impossible. On the side of the main body of the starter will be a 10-digit Bosch number which will be in the format of 0 001 abc xyz. You will need this number to find a brush pack, the bushes and anything else you may find that's worn. If you let me know the number i can look to see what's available for your starter. However from everything you describe, i'd say you would almost certainly be better off obtaining an exchange unit or if you're going to sell the old car, a good secondhand unit. Lastly, would i be right in assuming that the car the "slim" starter came from was manual and the other automatic?
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ |
|
The Following User Says Thank You to Laird Scooby For This Useful Post: |
Feb 23rd, 2021, 09:24 | #3 | |
Not an expert but ...
Last Online: Today 14:34
Join Date: Dec 2001
Location: Boncath
|
Quote:
I don't think that is the difference. I have a collection of about half a dozen starters all removed from manual cars, and they vary, some are fat, some slim. My current 1991 SE has an orginal slim line, and I'm pretty sure the Torslanda did too. The older cars, from the 80s, had the thicker starters. |
|
The Following 2 Users Say Thank You to Clifford Pope For This Useful Post: |
Feb 23rd, 2021, 11:30 | #4 | |
Premier Member
Last Online: Today 10:55
Join Date: May 2012
Location: Lakenheath
|
Quote:
However it doesn't always follow, especially with cars of that age as Bosch were developing starters that were slimmer and lighter but produced comparable power. Won't know for sure until the OP reports the Bosch number on it.
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ |
|
The Following User Says Thank You to Laird Scooby For This Useful Post: |
Feb 23rd, 2021, 17:22 | #5 |
New Member
Last Online: Feb 8th, 2024 14:01
Join Date: Dec 2009
Location: Market Drayton
|
Thanks to all who have commented. The Bosch number on the starter seems to be 0 001 108 088 (but the last digit is not clear owing to corrosion: it could be a 9).
The donor car, the 240DL, is manual B23. 1987. I think there is too much wrong with it to sell (but it would be handy not to have a rotting hulk on the driveway!) To be clear, the (good) starter from the 1987 DL is "fat"; the faulty starter came from the 1991 Torslanda. I have now managed to remove the two long bolts (and a good quality 7mm socket was correct) and I am just going to consult YouTube to see how to withdraw the lever. |
The Following User Says Thank You to John Halford For This Useful Post: |
Feb 23rd, 2021, 17:51 | #6 | |
Premier Member
Last Online: Today 10:55
Join Date: May 2012
Location: Lakenheath
|
Quote:
If it looks like this then you have the rubber block between the D/E bracket and body : That's a 1.4kW starter by the way. Also appears to be a reduction drive as well - higher torque for starting. https://www.woodauto.com/product/STR72006 https://www.woodauto.com/bom/66127/BOSCH-0001108088 First link is to the starter, second is the BOM (Bill of Materials) which is basically a catalogue of the parts in it.
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ Last edited by Laird Scooby; Feb 23rd, 2021 at 17:53. Reason: Additional info on red. drive |
|
Feb 23rd, 2021, 20:56 | #7 |
MY 240 DRIVES ME!
|
I have a horribly sluggish 240DL..When i procured the car the starter motor sounded like a bag of spanners when cranking..Two bolts off the the bell housing and good bearing grease on the throw out shaft and all was good..HJ.
|
The Following User Says Thank You to honestjoe For This Useful Post: |
Feb 24th, 2021, 14:07 | #8 |
Premier Member
Last Online: Oct 26th, 2023 20:42
Join Date: Jun 2010
Location: Thurrock
|
As a benchmark, before spending more time and possibly money, how much would one of the good helpful Volvo dealers (yes there are some) charge for a starter motor. It could be horrendous, or it could be a good surprise. To follow on, take both starter motors to a trusted local auto electricians.
Re the donor car, does it need to be a rotting hulk? I do hope some of what I say there might help. . |
Feb 24th, 2021, 15:49 | #9 | |
Experienced Member
Last Online: Today 11:44
Join Date: Jun 2007
Location: L/H side
|
Quote:
__________________
My comments are only based on my opinions and vast experience . |
|
The Following User Says Thank You to Clan For This Useful Post: |
Feb 24th, 2021, 19:01 | #10 | |
Premier Member
Last Online: Today 10:55
Join Date: May 2012
Location: Lakenheath
|
Quote:
It's just a different way of doing the same job and yes, the reduction drives (epicyclic geraboxes if you prefer) do wear, particularly the bush in the centre of them but they still do the job well despite being noisy when worn.
__________________
Cheers Dave Next Door to Top-Gun with a Honda CR-V & S Type Jag Volvo gone but not forgotten........ |
|
Tags |
240, starter problems |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|