How to Replace the Hazard Light Switch
Here we go with another guide requested. It is for a small part of the car, but it seems that many people have been having problems with their Hazard Light Switch.
There are 2 ways to remove the Hazard Light Switch. I have followed both ways and posted photos so you can choose whichever you think is easier to follow First of all remove the fascia form the heater control panel. I use my Leatherman blade to prise it off from one side and then the other. http://i157.photobucket.com/albums/t...h/Hazard01.jpg Undo all four screws http://i157.photobucket.com/albums/t...h/Hazard02.jpg The Heater Control Unit is also secured by this clip on that slot. To remove the Heater Control Unit you need to push it in slightly and it will prise off easily. Pay attention when you put everything back together as you must make sure you secure it back the correct way. http://i157.photobucket.com/albums/t...h/Hazard03.jpg There are two connectors plugged in the Heater Control Unit. Best way to remove it is to push it in diagonally and unclip the first connector. http://i157.photobucket.com/albums/t...h/Hazard04.jpg You can then remove the Heater Control Unit partially outwards and unplug the second connector http://i157.photobucket.com/albums/t...h/Hazard05.jpg Now here is where there are two ways to do it. I personally use the first method, as I am used to it and I know where and what the parts look like. Method 1 Put your hands in there and try to feel the two clips securing the Hazard Light Switch. See the next two images to get an idea of what you should be feeling for. http://i157.photobucket.com/albums/t...h/Hazard06.jpg You need to push the two clips gently inwards and push the Hazard Light Switch inwards http://i157.photobucket.com/albums/t...h/Hazard07.jpg A close up: http://i157.photobucket.com/albums/t...h/Hazard08.jpg You will need to wiggle out the switch so it is in this position. Then you can easily unclip it and replace it with your new switch. http://i157.photobucket.com/albums/t...h/Hazard09.jpg Method 2 This is the method I used the very first time I had to replace my Hazard Light Switch. It is a lot more trickier in my opinion and you face a small risk of breaking something, or losing small bits. You will need to remove both vents. Again, I used my trusted Leatherman to prise off each vent. http://i157.photobucket.com/albums/t...h/Hazard10.jpg This is a bit tricky too if it is the first time you have ever tried it. You need to push those clips downwards. See also next photo. The best way I found out is to do the right side one first and pull the fascia outwards and then do the left hand side one http://i157.photobucket.com/albums/t...h/Hazard11.jpg http://i157.photobucket.com/albums/t...h/Hazard12.jpg Then you just pull out the fascia outwards and very easily disconnect the Hazard Light Switch and replace it with the new one http://i157.photobucket.com/albums/t...h/Hazard13.jpg JOB DONE And here are some close up images of the switch. If you want to take it apart to try to repair it, you need to push in this clip and do the same on the other side http://i157.photobucket.com/albums/t...h/Hazard14.jpg http://i157.photobucket.com/albums/t...h/Hazard15.jpg This small metal bit is the one moving from left to right locking and unlocking the Hazard Light Switch. The tip of it moves in some grooves which makes it move from left to right. I have tried in the past to repair an old Hazard Light Switch I had but had no luck whatsoever with it. http://i157.photobucket.com/albums/t...h/Hazard16.jpg |
Yet another superb guide. Since this seems to be a common fault this will be very helpful for those wanting to fix it ( like me )
Thanks Gatos for taking the time again to do the guide :thumbs_up: |
I tested the 4 hazard light switches I had and 3 of them were fine. The 4th one was stuck and that is the one I took apart.
One of them is yours Volvo2002, and I need to find out who was the other person who asked me for one. |
Thanks CAT MAN
|
Quote:
|
hey alex , i notice your toolkit seems to use the leatherman a lot .....im happy to send you over a small flat bladed screwdriver !!!!
cheers from NZ |
I like it :thumbs_up:
It seems those plastic or metal things, moving left and right, are common weak points for generally all push-switches. |
Quote:
Since then, I have learned how to use it a lot more carefully |
Another clever guide for the Articles section, Gatos :thumbs_up:
|
Fitted today and working perfectly. Used Method 1
Unfortunately I found this job a bit of an annoyance. My hands aren't small so I found inserting the new switch in and connecting the plug onto the back a bloody nightmare. After much determination I got the plug in and the new switch fitted. The old switch appears to engage whenever it feels like it. The guide was very well explained and I rate it highly. Just don't be a idiot like me and damage the three ventilation knobs in the process :D |
All times are GMT +1. The time now is 15:28. |
Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.